Yaesu FTDX10

Yaesu FTDX10 firmware

Yaesu · FTDX10 · FTDX10 · HF transceiver

Latest firmware for the Yaesu FTDX10 is v1.15 (February 29, 2024).

Specifications

FTDX10 specifications

Type
Amateur HF/VHF transceiver
Frequency range
TX: 10-160 m + WARC and 60 m / 6 m (Also 4 m for Europe) / RX: 0.03-75 MHz
Modes
AM / FM / SSB / CW / RTTY / PSK
Show the full specification

General

Mode
AM / FM / SSB / CW / RTTY / PSK
Type
Amateur HF/VHF transceiver
Weight
5.9 Kg (13 lb)
Power supply
13.8 VDC ±15% (4-pin)
Tuning steps
1 / 10 Hz (SSB/CW) 10 / 100 Hz (AM/FM)
Other features
Hybrid SDR. 5" color touch TFT. 12 KHz, 3 KHz and 500 Hz roofing filters. RMDR more than 116 dB. 3rd IMDR better than 109 dB. 250 MHz HRDDS. 3D spectrum stream. Hi-speed ATU with 100 memories. SD card slot. CAT control. RS-232C. USB A/B. DVI. CTCSS/PL.
Frequency range
TX: 10-160 m + WARC and 60 m / 6 m (Also 4 m for Europe) RX: 0.03-75 MHz
Dimensions (W*H*D)
266*91*263 mm (10.47*3.58*10.35")
Frequency stability
±0.5 ppm @ 0 to 50°C (32 to 122°F), after 1 minute warmup
Repeater shift / offset
10 m: 0-1 MHz in 10 KHz steps 6 m: 0-4 MHz in 10 KHz steps
Channels / memory management
99 regular with alpha tags (12 characters) 5 QMB (Expandable to 10) 9 scan edge pairs (PMS) Non-volatile EEPROM storage
Antenna impedance / connector
50 ohm / SO-239 (16.7-150 ohm HF and 25-100 ohm 6 m with ATU on)
Current drain / power consumption
RX: 3 A TX: Max 23 A

Miscellaneous

Manufactured
2020-202x

Receiver Section

Selectivity
Mode-6 dB-60 dB AM6 KHz15 KHz FM12 KHz25 KHz SSB2.4 KHz3.6 KHz CW500 Hz750 Hz
Sensitivity
AM (10 dB S/N, 6 KHz BW) 0.5-1.8 MHz: 7.9 uV 1.8-30 MHz: 2 uV 50-54 MHz: 1 uV 70.0-70.5 MHz: 2 uV FM (15 dB SINAD, 12 KHz BW) 28-30 MHz: 0.25 uV 50-54 MHz: 1 uV 70.0-70.5 MHz: 0.25 uV SSB/CW (10 dB S/N, 2.4 KHz BW) 1.8-30 MHz: 0.16 uV 50-54 MHz: 0.125 uV 70.0-70.5 MHz: 0.16 uV
Image rejection
70 dB (HF) 60 dB (6 & 4 m)
Receiver system
Double conversion superheterodyne 1st IF: 9.005 MHz 2nd IF: 24 KHz
AF output power / speaker
2.5 W at 10% distortion / 4 ohm
External speaker connector
TS "Minijack" (3.5 mm), 4-16 ohm

Transmitter Section

RF output power
HF6 m AM:5-25 W5-25 W FM:5-100 W5-100 W SSB (PEP):5-100 W5-100 W CW:5-100 W5-100 W
Modulation system
AM: Low-level (Early stage) FM: Variable reactance SSB: Balanced
Spurious emissions
Better than -50 dB (HF) Better than -63 dB (6 m) Better than -60 dB (4 m)
Microphone input level
? mV
Max FM deviation (Factory set)
Normal: ±5 KHz Narrow: ±2.5 KHz
Microphone impedance / connector
200 ohm to 10 Kohm (600 ohm nominal) / 8-pin (Modular)

Changelog

FTDX10 firmware changelog

  1. v1.15 first tracked Fixes decoding halt during PTT transmission in RTTY/PSK modes and adjusts 50MHz repeater shift default.

Firmware history

All versions below were published by Yaesu on yaesu.com. Third-party and modified firmware is never listed.

  1. Version 1.15 Latest Released Feb 29, 2024 First seen Sep 6, 2026

    Fixes decoding halt during PTT transmission in RTTY/PSK modes and adjusts 50MHz repeater shift default. — summary by updatemystuff.com

    Source: yaesu.com

    Show release notes

    FTDX10 Firmware Update Information Download the FTDX10 [ FTDX10_Firmware_update_202402.zip] from the following website: https://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=1AB BC23C7EC57175A35CB0FDE7A639A0&DivisionID=65&isArchived=0 [FTDX10_Firmware_update_202402 ]zip Contains:

    • MAIN: V01-15 /FTDX10_MAIN_V0115. SFL 2/29/24 (New)
    • DISPLAY: V01-06 /FTDX10_DISPLAY_V0106. SFL 2/29/24 (New)
    • DSP: V01-20 /FTDX​10_IFDSP_V0120. SFL 8/1/23
    • SDR: V01-00 /FTDX10_SDR_V0100. SFL 4/7/21
    • AF: V01-00 /FTDX10_AFCPU_V0100. SFL 4/7/21
    • Firmware_Ver_Up_Manual_ENG_FTDX10_2104- B 4/9/21 Implements improvements:

    Update: MAIN V01-15 (2/29/24)

    1. Fixed the issue when sending from PTT, while the decoding screen (RTTY/PSK) is displayed, d​ecoding stops.
    2. Changed the default value of 50MHz BAND repeater shift frequency (1MHz→500 kHz).

    SD Card Preparation Refer to FTDX10 Operation Manual (2102K-CS-6) Page 78 [Formatting a SD card].

    If you already have the above firmware versions, it is not necessary to update the FTDX10 again.

    We hope this new firmware will increase your enjoyment of your FTDX10.

    Thank you for choosing Yaesu radios.

    If you have any problems or questions, please contact Yaesu Amateur Tech Support [email protected] .

    Yaesu USA | 6125 Phyllis Drive | Cypress, CA 90630 | 714.827-7600 | FAX: 714.827-8100 http://www.yaesu.com

    Release notes & download

Watch the FTDX10 for updates

Get an email the moment Yaesu publishes new firmware. Just your email — no account or password needed.

More Yaesu hf transceivers we track