Yaesu FT-710

Yaesu FT-710 firmware

Yaesu · FT-710 · FT-710 · HF transceiver

Latest firmware for the Yaesu FT-710 is v1.12 (February 29, 2024).

Specifications

FT-710 specifications

Type
Amateur HF/VHF transceiver
Frequency range
TX: 10-160 m + WARC / 6 m (And 4 m for Europe) / RX: 0.03-75 MHz
Modes
AM / FM / SSB / CW
Show the full specification

General

Mode
AM / FM / SSB / CW
Type
Amateur HF/VHF transceiver
Weight
4.5 Kg (9.92 lb)
Power supply
13.8 VDC ±15% (4-pin connector)
Tuning steps
1 / 5 / 10 / 20 Hz (AM/SSB/CW) 100 Hz (FM)
Other features
CTCSS/PL. 4.3" color TFT. 3D spectrum. DVI display port. Width & bandwidth shift. Contour feature. SD card slot. Voice recording. AESS (Acoustic Enhanced Speaker System).
Frequency range
TX: 10-160 m + WARC / 6 m (And 4 m for Europe) RX: 0.03-75 MHz
Dimensions (W*H*D)
239*80*247 mm (9.41*3.15*9.72")
Frequency stability
±0.5 ppm @ 0 to 50°C (32 to 122°F), after 1 minute warmup
Repeater shift / offset
±0-1 MHz in 10 KHz steps (10 m) ±0-4 MHz in 10 KHz steps (6 m)
Channels / memory management
99 regular with alpha tags (12 characters) 5 QMB (Expandable to 10) 9 scan edge pairs (PMS) Non-volatile EEPROM storage
Antenna impedance / connector
50 ohm / SO-239 (16.7-150 ohm HF and 25-100 ohm 6 m with ATU on)
Current drain / power consumption
RX: 1.8 to 2.2 A TX: Max 21 A

Miscellaneous

Manufactured
Japan, 2022-202x

Receiver Section

Selectivity
Mode-6 dB-60 dB AM6 KHz15 KHz FM12 KHz25 KHz SSB2.4 KHz3.6 KHz CW500 Hz750 Hz
Sensitivity
AM (10 dB S+N/N, 6 KHz BW) 0.5-1.8 MHz: 6.3 uV 1.8-30 MHz: 2 uV 50-54 MHz: 1 uV 70.0-70.5 MHz: 2 uV FM (15 dB SINAD, 12 KHz BW) 28-30 MHz: 0.25 uV 50-54 MHz: 0.2 uV 70.0-70.5 MHz: 0.25 uV SSB/CW (10 dB S+N/N, 2.4 KHz BW) 1.8-30 MHz: 0.16 uV 50-54 MHz: 0.125 uV 70.0-70.5 MHz: 0.16 uV
Image rejection
70 dB (HF) 60 dB (6 m)
Receiver system
Direct sampling superheterodyne / SDR technology IF: 18 KHz (SSB/CW) - 24 KHz (AM/FM)
AF output power / speaker
2.5 W at 10% distortion / 4 ohm
External speaker connector
TS "Minijack" (3.5 mm), 4-16 ohm

Transmitter Section

RF output power
HF6 m4 m AM:25 W25 W25 W FM:100 W100 W100 W SSB (PEP):100 W100 W100 W CW:100 W100 W100 W
Modulation system
AM: Low-level (Early stage) FM: Variable reactance SSB: Balanced
Spurious emissions
Better than -50 dB (HF) Better than -63 dB (6 m)
Microphone input level
? mV
Max FM deviation (Factory set)
Normal: ±5 KHz Narrow: ±2.5 KHz
Microphone impedance / connector
200 ohm to 10 Kohm (600 ohm nominal) / 8-pin (Modular)

Changelog

FT-710 firmware changelog

  1. v1.12 first tracked Fixes RTTY monitor sound and SCU-LAN transmitted audio echo, changes 50MHz repeater shift default.

Firmware history

All versions below were published by Yaesu on yaesu.com. Third-party and modified firmware is never listed.

  1. Version 1.12 Latest Released Feb 29, 2024 First seen Sep 6, 2026

    Fixes RTTY monitor sound and SCU-LAN transmitted audio echo, changes 50MHz repeater shift default. — summary by updatemystuff.com

    Source: yaesu.com

    Show release notes

    FT-710 Firmware Update Information Download the FT-710 [FT-710_Firmware_update_202 402.zip] from the following website: https://www.yaesu.com/indexVS.cfm?cmd=DisplayProduct​s&ProdCatID=102&encProdID=615 ADFEAB5EDBC65EBE1D64835F209DB&DivisionID=65&isArchived=0 [FT-710_Firmware_update_202402 ]zip Contains:

    • MAIN: V01-12 /FT-710_MAIN_V011 2.SFL 2/29/24 (New)
    • DISPLAY: V01-08 /FT-710_DISPLAY_V0108. SFL 7/5/23
    • DSP: V01-01 /FT-710_IFDSP_V0101. SFL 3/27/23
    • SDR: V01-04 /FT-710_SDR_V0104. SFL 3/27/23
    • Firmware_Ver_Up_Manual_ENG_FT-710_2211A 11/14/22 Implements improvements:

    Update: MAIN V01-12 (2/29/24)

    1. Fixed a bug with RTTY monitor sound.
    2. Corrected the phenomenon where echo was applied to the transmitted audio when connected to SCU-LAN.
    3. Changed the default value of 50MHz BAND repeater shift frequency (1MHz→500kHz) .
    4. Other functional improvements and optimizations have been made.

    SD Card Preparation Refer to FT710 Operation Manual ( 2209E-AS) Page 68 [Formatting a SD card].

    How to Confirm the Firmware Version Complete update of DISPLAY firmware first, then install updates of MAIN, DSP and SDR firmware.

    Refer to FT -710 Firmware Upgrade Manual After installing the firmware completely, the FT- 710 must be reset: Turn the Main Power OFF, then press [DSP REST] and [FINE/FAST] buttons together, while pressing the Main Power ON.

    Main frequency display ​7.000.000 MHz will appear.

    If you already have the above firmware versions, it is not necessary to update the FT-710 again.

    We hope this new firmware will increase your enjoyment of your FT-710.

    Thank you for choosing Yaesu radios.

    If you have any problems or questions, please contact Yaesu Amateur Tech Support [email protected] .

    Yaesu USA | 6125 Phyllis Drive | Cypress, CA 90630 | 714.827-7600 | FAX: 714.827-8100 http://www.yaesu.com

    Release notes & download

Watch the FT-710 for updates

Get an email the moment Yaesu publishes new firmware. Just your email — no account or password needed.

More Yaesu hf transceivers we track