Yaesu FTDX101MP

Yaesu FTDX101MP firmware

Yaesu · FTDX101MP · FTDX101MP · HF transceiver

Latest firmware for the Yaesu FTDX101MP is v1.22 (November 17, 2025).

Specifications

FTDX101MP specifications

Type
Amateur HF/VHF transceiver
Frequency range
TX: 10-160 m + WARC and 60 m / 6 m / RX: 0.03-75 MHz / (The European version also features 4 m/70 MHz)
Modes
AM / FM / SSB / CW / RTTY / PSK
Show the full specification

General

Mode
AM / FM / SSB / CW / RTTY / PSK
Type
Amateur HF/VHF transceiver
Weight
13.5 Kg (29.8 lb)
Power supply
Mains (FPS-101 external PSU with speaker, included as standard)
Tuning steps
1 / 5 / 10 Hz (SSB/CW) 10 / 100 Hz (AM/FM)
Other features
CTCSS/PL. Voice memory. Dimmer. RTTY and PSK encode/decode. SD/SDHC card slot. Clock. 7-inch full color touch TFT. Twin RX. VC-tune units for both main and sub RX included from factory.
Frequency range
TX: 10-160 m + WARC and 60 m / 6 m RX: 0.03-75 MHz (The European version also features 4 m/70 MHz)
Dimensions (W*H*D)
420*130*355 mm (16.6*5.1*12.7")
Frequency stability
±0.1 ppm @ -10 to +60°C (14 to 140°F), after 1 minute warmup
Repeater shift / offset
±0-1 MHz in 10 KHz steps (10 m) ±0-4 MHz in 10 KHz steps (6 m)
Channels / memory management
99 regular (Can be organized into 6 groups with 20 memories in each) 9 PMS pairs
Antenna impedance / connector
50 ohm (ATU off)/ Three SO-239 HF: 16.7-150 ohm (ATU on) 6 m: 25-100 ohm (ATU on)
Current drain / power consumption
RX: 100 to 120 VA TX: Max 720 VA

Miscellaneous

Manufactured
Japan, 2019-202x

Receiver Section

Selectivity
AM (BW=6 KHz. Width=Center) 6 KHz (-3 dB) 15 KHz (-60 dB) FM (BW=12 KHz. Width=Center) 12 KHz (-6 dB) 25 KHz (-60 dB) SSB (BW=2.4 KHz. Width=Center) 2.4 KHz (-3 dB) 3.6 KHz (-60 dB) CW (BW=500 Hz) 500 Hz (-3 dB) 750 Hz (-60 dB)
Sensitivity
AM (10 dB S+N//N. BW=6 KHz) 0.5-1.8 MHz: 6.3 uV 1.8-30 MHz: 2 uV (Amp2 on) 50-54 MHz: 1 uV (Amp2 on) 70-70.5 MHz: 2 uV (Amp2 on), Europe only FM (12 dB SINAD. BW=12 KHz. Amp2 on) 28-30 MHz: 0.25 uV 50-54 MHz: 0.2 uV 70-70.5 MHz: 0.25 uV, Europe only SSB/CW (10 dB S/N. BW=2.4 KHz. Amp2 on) 1.8-30 MHz: 0.16 uV) 50-54 MHz: 0.125 uV 70-70.5 MHz: 0.16 uV, Europe only
Image rejection
HF: 70 dB 6 m: 60 dB
Receiver system
Double conversion superheterodyne 1st IF: 9.005 MHz (Main) - 8.9 MHz (Sub) 2nd IF: 24 KHz (Main/Sub)
AF output power / speaker
2.5 W at 10% distortion / 4 ohm
External speaker connector
3.5 mm, 4-16 ohm

Transmitter Section

RF output power
HF6 m4 m AM:50 W50 W50 W FM:200 W200 W200 W SSB (PEP):200 W200 W200 W CW:200 W200 W200 W RTTY/PSK:200 W200 W200 W
Modulation system
AM: Low-level, early stage FM: Variable reactance SSB: Balanced
Spurious emissions
HF: Better than -50 dB 6 m: Better than -66 dB
Microphone input level
? mV
Max FM deviation (Factory set)
FM: ±5 KHz NFM: ±2.5 KHz
Microphone impedance / connector
200 ohm to 10 Kohm (600 ohm nominal) / 8-pin (Metal locking ring connector)

Changelog

FTDX101MP firmware changelog

  1. v1.22 first tracked Added FT8 PRESET for quick setup and fixed menu settings loading, PSK mode, and CAT errors.

Firmware history

All versions below were published by Yaesu on yaesu.com. Third-party and modified firmware is never listed.

  1. Version 1.22 Latest Released Nov 17, 2025 First seen Sep 6, 2026

    Added FT8 PRESET for quick setup and fixed menu settings loading, PSK mode, and CAT errors. — summary by updatemystuff.com

    Source: yaesu.com

    Show release notes

    FTDX101MP/D Firmware Update Information Download the FTDX101MP/D [ FTDX101_Firmware_update_202105.zip] from the following website: https://www.yaesu.com/?cmd=DisplayProducts&DivisionID=65&ProdCatID=102 FTDX101 Firmware update_202105.zip Contains:

    • MAIN: V01-22 /FTDX101_MAIN_V0122 .SFL 5/14/21 (New)
    • DISPLAY: V01-08 /FTDX101_DISPLAY_V0108. SFL 4/7/21
    • DSP: V01-07 /FTDX101_IFDSP_V0107. SFL 4/7/21
    • SDR: V02-06 /FTDX101_SDR_V0206. SFL 4/7/21
    • AF DSP: V01-00 /FTDX101_AFDSP_V0100. SFL 4/7/21
    • Firmware_Ver_Up_Manual_ENG_FTDX101MP_D_2004-D 4/9/21 Implements improvements (5/14/21) New:
    1. Fixed a bug that the "MENU" settings of the previous firmware version (saved on the SD card) were not loaded correctly after writing the new firmware.
    2. Fixed a bug that "PRESS" operation becomes an error when selecting ​"PEAK" level in the "FUNC" menu.
    3. The operating mode during PSK operation has been changed from "PSK-LSB" to "PSK-USB".*
    4. The default operating setting of the ANT3 / RX terminal has been changed from "TRX" to "RX- ANT" (receive only).
    5. Fixed a CAT command error when using the RS232C port.
    6. Other functional improvements and optimizations have been made.

    Note: The update Operation Manual [FTDX101MP_D_OM_ENG_EH068H213_2102P -JS-3.pdf] 5/14/21 is available on the Yaesu website.

    • For “PSK” mode , set the operation mode of the data communication software application on the PC to “DATA-U”.

    Implements improvements (4/9/21):

    1. The [PRESET] Function has been newly added to the MODE screen to quickly facilitate "FT8" operation. The optimum setting values for the "FT8" Communications Mode may be enabled with one-touch of [PRESET]. (The Operation Mode Selection Screen is displayed by pressing the MODE key). "FT8" set-up is efficient and effortless. Also, the settings of the 14 [PRESET] items can be called and changed by pressing and holding [PRESET].
    2. When transmitting with the waterfall displayed, the screen switches to the transmission scope display. The receive status displayed just before the start of transmission is displayed on the screen after the end of transmission (return to receive status), and then the latest receive waterfall will again be displayed continuously. (Maximum scope display time)
    3. The initial value (factory default setting) of the TX bandpass filter setting (RADIO SETTING (MODE SSB)  TX BPF SEL) in SSB mode has been changed to "100 - 2900Hz".
    4. When no dial operation function is assigned to the MPVD (Multifunction Dial), it sequences as "FAST" (10 times the frequency variable of the VFO dial).
    5. The set and default values of the CW TX rise & fall waveform characteristics (CW SETTING  MODE CW  CW WAVE SHAPE) have been optimized. (Set values: 4/6/8 msec, default value: changed to 6 msec)
    6. The number of input digits of the transmit CW contest number has been changed from 3 digits to 4 digits (1 to 9999).
    7. Fixed a bug that the SWR meter fluctuates greatly for a moment at the start of CW transmission.
    8. Fixed a bug that modulation may not be applied when transmitting using voice memory.
    9. Fixed a bug that the contents of the voice memory are not cleared when "ALL RESET" is applied in the "RESET" menu (EXTENSION SETTING  RESET).
    10. Fixed a bug that POWER does not appear when the power is turned OFF in PSK mode, the powe​r is turned ON again in the same mode, and PSK text memory transmission is performed.
    11. Improvements and optimizations have been made in operations of the CAT control commands.
    12. Other improvements and optimizations.

    SD Card Preparation Refer to FTDX101MP/D Operation Manual (2102P-JS-2) Page 80 [Formatting a SD card].

    If you already have the above firmware versions, it is not necessary to update the FTDX101MP/D again.

    We hope this new Firmware will increase your enjoyment of your FTDX101MP/D.

    Thank you for choosing Yaesu radios.

    If you have any problems or questions, please contact Yaesu Amateur Tech Support [email protected] .

    Yaesu USA | 6125 Phyllis Drive | Cypress, CA 90630 | 714.827-7600 | FAX: 714.827-8100 http://www.yaesu.com

    Release notes & download

Watch the FTDX101MP for updates

Get an email the moment Yaesu publishes new firmware. Just your email — no account or password needed.

More Yaesu hf transceivers we track