TASCAM Sonicview 16XP / TASCAM Sonicview 16dp firmware v1.6.0

< New functions >

• Audio Follow Video functions newly added.
• OA Tally Inhibit Settings has been added to the Preferences screen.
• Monitor Add function newly added. This allows for the mixing and monitoring of multiple sources.
• Location settings are now available in the Monitor screen.
• The LOCK SETUP screen has been redesigned. This allows more detailed settings of lock items.
• The Version Information screen has been redesigned, allowing the user to check the status information of the version of the device connected to the main unit.
• Stereo-linked CH and ST IN1/2 modules can now have separate L/R settings for each item in the MODULE (INPUT) screen.
• Monitor stereo/mono switching is now possible with User Key, GPIO-IN, Foot Switch.
• A logical inversion setting has been added to the MUTE control function of GPIO-IN/Foot Switch.
• The THRESHOLD value of Compressor can now also be adjusted from the bar in the KEY IN meter.
• The following functions added to V1.6.0 have also been added to the User Defined Control:
• Audio Follow Video
• Monitor Add
• On Air Tally
• Monitor DIM
• The following functions have been added to the Talkback screen:
• "DIM" display function added when DIM is enabled.
• Talkback input location settings are now available.
• MON1/2 location disp​lay has been added.

< Maintenance items >

• The MODULE (INPUT/OUTPUT) screen has been redesigned.

This allows for easier monitoring of multiple assigned output ports, especially in the MODULE (OUTPUT) screen.

• Specifications have been changed so that functions set to ON in GPIO-IN/Foot Switch can be turned ON/OFF using the physical buttons, User Key, and screen buttons on the main unit.
• The lower limit of the THRESHOLD value for DUCKER has been changed from -30 dB to -60 dB.
• When turning on the main unit, GPIO-OUT with assigned User Key OUT would not output as set. This has been fixed.
• The Snapshot Lock state would not be saved in All System Data. This has been fixed.
• When loading a non-MAIN L/R registered All System Data file to the master module, the master module would change to MAIN L/R. This has been fixed.
• Data was not updated after overwriting a file with the same name when exporting All System Data. This has been fixed.
• When connecting the Sonicview to a Windows PC via USB, some noise would occur at the start of playback in some applications. This has been fixed.
• When the sample rate on a Windows PC was set to 96 kHz and a sound source was ​playing on it, if the Sonicview was turned on/off audio was not output correctly while the sound source was being played. This has been fixed.
• The GPIO-IN/Foot Switch pin input state was different from the GPIO-IN/Foot Switch pin input state when starting up the main unit and when reading All System Data. This has been fixed.
• When a stereo module was assigned to the Compressor and Ducker Key In Source, the Key In meters and gain reduction would operate in mono. This has been fixed.
• When backing up All System Data to a USB flash drive, all System Data could not be backed due to an insufficient capacity alert. This has been fixed.
• After backing up All System Data to a USB flash drive or SD card for the first time, files were not displayed when the RESTORE screen was opened. This issue has been fixed.
• Specifications have been changed so that SOLO is turned off after Factory Reset and All System Data Load.
• After Factory Reset, Paste MODULE or UNDO/REDO would be performed. This has been fixed.
• The User Key did not light up in the following case:

When the SB-16D's GPIO-OUT port is set to Local and the corresponding GPIO-OUT port is assigned to Parameter 2 of LED Indication > GPIO-OUT in the User Key setting of the Sonicview main unit. This has been fixed.

• When setting SB-16's GPIO-IN performance mode to "ALL Local", the Sonicview GPIO-IN would also operate. This has been fixed.
• When an SB-16D was mounted to the Sonicview, regardless of the settings, all SB-16D GPIO-OUTSs would turn to OPEN. This has been fixed.
• Improved meter display.
• Operation stability has been improved.