TASCAM Sonicview 16XP / TASCAM Sonicview 16dp firmware v1.5.0

< New functions >

• Snapshot Recall has been speeded up.
• The following monitor-related features have been added/changed:
• The monitor feature now supports 2 channels; the MON2 output is connected to the Output Router.
• MIC LOCATION settings (Control Room / Studio / NONE) can be applied to each MON1 and MON2.
• Direct OUT function newly added. Signals are output just before Monitor Mute and DIM.
• SOLOR output can now be output externally via Output Router.

Also, a setting has been added to prevent switching Monitor to SOLO when SOLO output is being output ​externally.

• MONITOR FOLLOW function newly added.

MON1 FOLLOW switched the MON2 signal to MON1. On the other hand, MON2 FOLLOWS switches the MON1 signal to MON2.

• Monitor Exclusive function newly added. Two monitors can be set/switched as small or large speakers.
• Mic/Line input can now be selected in Monitor Source.
• Monitor Source can now be set independently for L /R ch.
• The following Talkback-related functions have been added/changed:
• While talkback is in action, the DIM level applied to the monitor can now be independently set from the normal monitor DIM level.
• Any input terminal can now be selected for talkback input.
• Talkback signals can now be output externally.
• The Talkback signal that cuts into bus has been changed to post-fader.
• The following User Key/Foot Switch / GPIO-IN-related functions have been added/changed:
• All support monitor-related changes.
• All support Talkback-related changes.
• Oscillator function and ON/OFF settings have been added.
• LED Indication has been added. The User Key LED will light up in conjunction with the GPIO-IN/OUT Open/Closed function.
• Any output terminal can be selected for SOLO output.
• USER KEY OUT function added to GPIO-OUT. Pulses are output from GPIO-OUT when pressing the USER KEY.
• New settings added to Solo/Mute/Fader Speed. ON/OFF on SOLO/MUTE and the fade in/out speed can be adjusted.
• Clock Synchronous Type settings added. This sets the sync status (Lock/Unlock) criteria between the main unit and the Dante signal.

< Maintenance items >

• The main unit was not recognized when the sample rate was changed from 96 kHz to 48 kHz from the Dante Controller. This has been fixed.
• In the screen display of Rch in the stereo-linked CH/MIX module, the item selected in SNAPSHOT RECALL SAFE was changed during Snapshot Recall. This has been fixed.
• When loading ALL SYSTEM DATA, the SB-16D mounting status would not be displayed correctly. This has been fixed.
• When the SENDS ON FADER is ON, the selected FX RTN fader would move when operating the MASTER FADER.

This has been fixed so that the INPUT LEVEL of the selected FX will move as in the TASCAM Sonicview main unit.

• When selecting the OUTPUT ROUTING/BUS CONFIG item on SNAPSHOT R​ECALL SAFE.

The output routing would be changed when recalling a snapshot. This has been fixed.

• When a snapshot with OSC assigned to Main LR was recalled, display of the OSC SETUP Screen did not correspond sometimes. This has been fixed.
• When performing a Factory Reset to SD-16D from the main unit, the Analog Gain and PAD were not set to the initial values. This has been fixed.
• On the INPUT SOURCE SELECT screen, the input port of the SB-16D mounted on Dante 33-48ch could not be assigned. This has been fixed.
• Analog Gain was not displayed when the SB-16D was connected via IF-DA64 and assigned to the CH module's INSERT RETURN on the CH module. This has been fixed.
• On the MODULE (OVERVIEW/INPUT) screen, the ON/OFF PAD of an unauthorized SB-16D would be displayed in reverse. This has been fixed.
• Issues in the Snapshot Import/Export screen have been fixed.
• All System Data screen display issues have been fixed.
• Port display issues have been fixed.
• Operation stability has been improved.