microHAM Station Master DeLuxe firmware
microHAM · Station Master DeLuxe · Station Master DeLuxe · Accessory
Latest firmware for the microHAM Station Master DeLuxe is v1.38 (October 9, 2020).
Changelog
Station Master DeLuxe firmware changelog
-
v1.29v1.31Non-Rx-safe Tx antennas now protected by band mechanism; automatic Rx/SubRx takeover; complex setup conflicts resolved. -
v1.27v1.28Added IC-7610 and IC-821H support with new PTT focus control and cross-focus rotator access. -
v1.25v1.26Adds UltraBeam RCU-06 support and reorganizes antenna device categories.
Firmware history
All versions below were published by microHAM on microham.com. Third-party and modified firmware is never listed.
-
Source:
microham.comRelease notes not published by vendor — see official page.
Release notes & download -
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Responses to commands MD0 and MD1 from FTdx101D was interpreted incorrectly.
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-9700 and FTdx101D added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- TS-890 added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- improved stability of communication between PC and SMD (config update)
-
Non-Rx-safe Tx antennas now protected by band mechanism; automatic Rx/SubRx takeover; complex setup conflicts resolved. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- non-Rx-safe Tx antennas included in same band protection mechanism
- upon Rx/SubRx takeover suggestion, same/different button is now automatic Yes/No
- fixed false conflicts of subRx path with Rx/Tx path of the same SMD in complex setups (together with module_relay v1.19)
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- support for locally connected rotator together with networked rotators in stack
-
Added IC-7610 and IC-821H support with new PTT focus control and cross-focus rotator access. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-7610, IC-821H added to the list
- automatic focus change upon PTT can be disabled
- see new menu item [m3]PTT Focus
- if PTT starts while rotator is being set, rotator setting is immediately applied
- if no rotator in current focus, rotators from other focus may be controlled
- related menu item [m4]Other Rota added
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Control of SteppIR(SDA100,10/20kHz) didn't work
-
Adds UltraBeam RCU-06 support and reorganizes antenna device categories. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR and UltraBeam devices (now collectively referred as MotorANT devices) are now categorized by range and type instead of model name.
- support for UltraBeam RCU-06
- tuning of UltraBeam initiated at 10kHz boundaries
- tuning of SteppIR with SDA 100 controller initiated at 50kHz boundaries and optionally at 10kHz or 20kHz boundaries (band dependent)
-
Adds support for Flex 6000/5000 and Apache Labs ANAN radios; fixes PTT lock at startup — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- some SDRs added to the list:
- Flex 6000 series (uses TS-990 protocol)
- Flex 5000 (uses TS-2000 protocol)
- Apache Labs ANAN 100/200 (uses TS-2000 protocol)
- Now PTT is not locked when TX frequency is out of SteppIR range upon startup
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- current rotator azimuth displayed when encoder only pressed (while retaining the previous functionality of all rotators stop)
-
Fixed automatic frequency reporting on Icom radios with CI-V transceive enabled. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Automatically reported operating frequency was ignored on Icoms with new firmware (when CI-V transceive was set to on):
IC-7100(fw v1.10(E4)+), IC-7300, IC-7600(fw v2.00+), IC-7700(fw v2.10+), IC-7800(fw v3.10+), IC-7850, IC-7851
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- Expert Electronics MB1 added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- improved rotator(v1.8)/data rotator(v1.21) azimuth reporting upon startup
- ANT unit in module_relay(v1.17) now obey frequency-band rules
- improved ANT unit handling for manual control from SMD properties
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- support for newer firmware versions of some ICOMs:
Icom IC-7100, fw v1.10(E4)+ Icom IC-7600, fw v2.00+ Icom IC-7700, fw v2.10+
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- iLink coupling to SMORF
- possibility to set software lock from router
- FT-991, IC-7850, IC-7851, IC-7800 fw v3.10+, IC-7300 added to the list
- fixed FT-900, FT-890, FT-840
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- Hilberling PT8000 added to the list
- Elecraft K3 protocol updated to Rev.E11 and extended by P3 protocol Rev.A4
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- FTdx1200 added to list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-7100 added to list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- support for Acom 2S1 now includes bandlock/contest protection (with module_data v1.17)
- improved path properties handling
- improved nonsplit-to-split switching
- temperature in Bratislava hit record with 39C today
-
Enhanced Acom 2S1 support, BUSY box visualization on PTT, and fixed subRx-split frequency handling. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- enhanced support for Acom 2S1 boxes (with module_data v1.16)
- implemented persistent path properties
- implemented displaying boxes causing BUSY when PTT
- increased EEPROM configuration space
- fixed problem when after subRx-split switched on, a frequency change was needed
- minor fixes for subRx items display
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed problem with paths containing multiple PAs
- added support for Acom 2S1 boxes (with module_data v1.15)
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- enhanced display of azimuths for certain types of stacks
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- adopted UltraBeam v1.36 protocol change
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: commands SB, DV was mistakenly included to K2 protocol
- bug fixed: SteppIR/SDA100 Remote Driver bit treated as "HAM mode"
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- added contest rule
- improved same-band protection in conjunction with Keyers
- added new radios to CAT, see Keyers changelog
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- added support for new UltraBeam models
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- updated control commands protocol
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- control commands protocol extensions implemented
- added delays in Acom2000 communication protocol (confirmed with manufacturer)
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed minor bug for switching between bands on the same multiband path while in non-split and same-band protection is not no-protection
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR/UltraBeam front panel settings for 180/bidir are retained
- for UltraBeam, tuning step changed to 25kHz
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- improved handling of SDA100
- modified behaviour of bandlock to protect also receivers out of bandlock bands
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- improved startup sequence of slave processors
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- First release of SMD firmware.
Watch the Station Master DeLuxe for updates
Get an email the moment microHAM publishes new firmware. Just your email — no account or password needed.
