microHAM Station Master firmware
microHAM · Station Master · Station Master · Accessory
Latest firmware for the microHAM Station Master is v2.41 (October 9, 2020).
Changelog
Station Master firmware changelog
-
v2.33v2.34Added UltraBeam RCU-06 support and reorganized antenna device categories by range and type -
v2.32v2.33Support added for Flex 6000/5000 and Apache Labs ANAN SDRs; PTT locking fixed at startup. -
v2.31v2.32Fixed automatic frequency reporting on newer Icom transceivers with CI-V transceive enabled.
Firmware history
All versions below were published by microHAM on microham.com. Third-party and modified firmware is never listed.
-
Source:
microham.comRelease notes not published by vendor — see official page.
Release notes & download -
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Responses to commands MD0 and MD1 from FTdx101D was interpreted incorrectly.
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-9700 and FTdx101D added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- TS-890 added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-7610, IC-821H added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Control of SteppIR(SDA100,10/20kHz) didn't work
-
Added UltraBeam RCU-06 support and reorganized antenna device categories by range and type — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR and UltraBeam devices (now collectively referred as MotorANT devices) are now categorized by range and type instead of model name.
- support for UltraBeam RCU-06
- tuning of UltraBeam initiated at 10kHz boundaries
- tuning of SteppIR with SDA 100 controller initiated at 50kHz boundaries and optionally at 10kHz or 20kHz boundaries (band dependent)
-
Support added for Flex 6000/5000 and Apache Labs ANAN SDRs; PTT locking fixed at startup. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- some SDRs added to the list:
- Flex 6000 series (uses TS-990 protocol)
- Flex 5000 (uses TS-2000 protocol)
- Apache Labs ANAN 100/200 (uses TS-2000 protocol)
- Now PTT is not locked when TX frequency is out of SteppIR range upon startup
-
Fixed automatic frequency reporting on newer Icom transceivers with CI-V transceive enabled. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: Automatically reported operating frequency was ignored on Icoms with new firmware (when CI-V transceive was set to on):
IC-7100(fw v1.10(E4)+), IC-7300, IC-7600(fw v2.00+), IC-7700(fw v2.10+), IC-7800(fw v3.10+), IC-7850, IC-7851
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- Expert Electronics MB1 added to the list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- support for newer firmware versions of some ICOMs:
Icom IC-7100, fw v1.10(E4)+ Icom IC-7600, fw v2.00+ Icom IC-7700, fw v2.10+
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- iLink coupling to SMORF
- possibility to set software lock from router
- FT-991, IC-7850, IC-7851, IC-7800 fw v3.10+, IC-7300 added to the list
- fixed FT-900, FT-890, FT-840
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- Hilberling PT8000 added to the list
- Elecraft K3 protocol updated to Rev.E11 and extended by P3 protocol Rev.A4
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- FTdx1200 added to list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- IC-7100 added to list
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- adopted UltraBeam v1.36 protocol change
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- bug fixed: commands SB, DV was mistakenly included to K2 protocol
- bug fixed: SteppIR/SDA100 Remote Driver bit treated as "HAM mode"
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- added new radios to CAT, see Keyers changelog
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- added support for new UltraBeam models
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- control commands protocol extensions implemented
- added delays in Acom2000 communication protocol (confirmed with manufacturer)
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR/UltraBeam front panel settings for 180/bidir are retained
- for UltraBeam, tuning step changed to 25kHz
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed problem with SDA100/BigIR
-
Fixes permanent BUSY when switch delay and break-before-make are both zero, improves CAT decoding at powerup — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed permanent BUSY if both switch delay and break-before-make are set to 0
- improved CAT decoding upon powerup
- added ALARM_ROTA_NEGATIVE for negative input to the rotator sensor
- bug fixed in IF command in Kenwood protocol
- multiple minor bug fixes
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- UltraBeam 180/bidir support added
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- UltraBeam support added
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR SDA100 support added
- AUX baudrate setting bug fixed
- KeyOut tail added
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- SteppIR control enhancements
- added Acom2000A PA control
-
Adds fully configurable PS/2 keypad, improved CAT decoding support, relay delays, and PA management options. — summary by updatemystuff.com
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- standalone CAT decoding
- new format of configuration data
- steppir protocol enhancements, version reported to router
- if available, yagi steppir bidir/180 turn used for [LP]
- added optional KeyIn inverting
- added break-before-make delay for ANT and BPF relays
- added always active rotator control option
- added PA standby and keep PA off options to FUNC menu
- PS/2 keypad is now fully configurable and individualkeys can be forwarded to Keyer
- added CIV option on auxiliary serial port
- added CAT input on auxiliary serial port (BandDecoder-like functionality)
- brake release after 15s idle during braked rotator calibration
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed inverted BCD outputs
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- fixed bug when inhibit lead = 0
- added alarms for KeyIn late or drop
- fixed KeyOut
- added SINK state for A/B voltage measurement
- fix for iLink coupling/uncoupling
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- added noTxAntenna lock to Keyer via I2C
- sleep mode command from keyer is accepted
-
Source:
microham.comRelease notes & downloadShow release notes Hide release notes
- First release of SM firmware.
Watch the Station Master for updates
Get an email the moment microHAM publishes new firmware. Just your email — no account or password needed.
