Accsoon CineView M7H Pro firmware v2026.04.16

– 2026

APRIL

UPDATE

– Release Date: 2026.04.16

UPDATE NOTE

• This update does not require a second time update.
• CineView M7H Pro Users SHOULD NOT UPDATE the HDMI In Driver.
• Only for CineView M7/M7 Pro users who updated straight to this version from prior to 2026 Jan Firmware:
• To take full advantage of this update, after the update, please go to Device Info. settings in the Product Feature settings panel (tap on the top status bar), then swipe down to HDMI In Driver and manually update the HDMI driver. Please note you will need to do this in Monitor Mode and connect your CineView M7 to a Wi-Fi network with Internet access.

• After update, the gamma setting in Calibration menu might be reset to “2.20” value. For customers working in professional broadcast environment, please remember to set the value back to “2.40”.

CAMERA CONTROL

• CineView M7 series now supports Canon XC protocol, enabling wireless camera control support for select Canon C series cameras.
• Validated Camera Models:

Canon’s latest EOS-C series lineup: C50 , C70 , C80 , C400 .

• Full Canon XC Camera Control Support:
• Intelligent IP connection
• Unlike some high-end monitors that require users to work through a long and often overcomplicated network setup process, CineView only requires y​ou to input the target camera IP address and verything else will be handled automaticallyby the smart operating system.

All you need to do is connect your CineView M7 to the camera hotspot or the LAN network your target camera is connected to, check the current IP address in the camera menu then input it in the special IP address input box on CineView M7 and that’s it.

• Optimized Imaging Parameter Mode Support
• The current Canon XC Camera Control integration fully supports both Gain Modes:

ISO

and db , and two Shutter Modes: Shutter Speed and Angle .

• Touch Focus Control
• Focus point control is also supported. It’s recommended to switch to a smaller AF detection box for better remote focus control.
• Expanded Camera Control Compatibility List
• Note1:

(All listed cameras were validated through internal tests. Models outside of the compatibility list may work, but are not guaranteed.)

• Note2:

(The “ Basic Support ” below includes ISO, Shutter Speed, Aperture, White Balance Preset and Custom WB Kelvinparameter controls, plus additional Focus Control and Record Trigger with optional Record Status Sync. Refer to prior release notes for more detailed guide and information.)

• Detailed List:

- USB-PTP

(Wired)

• Sony

- FX3

,

FX30

(Basic support with optimized support for EI & Shutter Angle mode)

• A7 Mark IV , A7s Mark III , A9 Mark III , A7c Mark II (Basic Support)
• Canon
• R5 , R5 Mark II , R6 , R6 Mark II , R7 , R8 .

(Basic Support)

• Nikon
• Z9 , Z8 (Basic Support)
• Z5 , Z50 , Z6 ,

Z6II

,

Z7 II

(Basic support but Focus Control unusable due to camera limitation)

- IP-PTP

(Wireless)

• Sony
• FX6 Special Optimization (Basic support with optimized support for EI/db & Shutter Angle mode) (*Please set physical WB toggle to “

PRE

” for accurate white balance control.)

- FX3

,

FX30

(Basic support with optimized support for EI & Shutter Angle mode)

• A7 Mark IV , A7s Mark III , A9 Mark III , A7c Mark II (Basic Support)
• IP-Canon XC (Wireless)
• Canon
• C50 , C70 , C80 , C400 (Basic support with optimized support for db & Shutter Angle mode)
• Guide on Canon C series camera control setup !!!
• Setting Up the Connection
• The Canon XC commands is based on HTTP protocol, therefore it’s only operational through IP conenction. You can either setup a camera hotspot or let the camera connect to an external network, both Wi-Fi and Ethernet connections work.

(*This guide can only serve as reference, this setup process may change with future Canon camera firmware updates.

If the following step-by-step guide no longer applies, just remember the core concept: configure the camera to setup its own hotspot or connect to an existing network, then connect CineView M7 to the same network and input the IP Address of the camera, then the app will handle everything else for you.)

• 1. Enable Network Connection To do this, you will need to go to the camera settings, switch to “Network Settings”, and enable the network connection.
• *Please bare in mind the C70 model does not have internal network support, you will need to use an external Wi-Fi or Ethernet adapter to enable network operation. Here is the official compatibility list from Canon https://support.usa.canon.com/kb/s/article/ART177792 .

If these models are hard to purchase in your region, please look for adapters using the most basic and universal chipset.

These solutions tend to have better compatiblity, but it’s not guaranteed.

In our tests, we found out an old but generic Ethernet adapter based on Realtek RTL8153 worked, while newer adapters did not.

We recommend searching for compatible adapters on YouTube and Reddit forums.

• 2. Start New Network Config Process Then disconnect existing network operation if present, go to “Conenction Settings”, Choose an empty unspecified slot, and select “Create New with Wizard”. Next Select “XC Protocol”, then select “Create New Comm. Setting”.
• 3. Choose Your Connection Method In the “Network Type” selection page, select the one you’d like to use for later connection.

If you’d like to host a camera hotspot, or let the camera connect to an external Wi-Fi network, choose Wi-Fi. If you’re connecting the camera to an external Ethernet network, choose Ethernet.

• Please do not use Ethernet adapter on CineView M7 and connect it directly to the cam​era’s RJ45 port. CineView M7 can not act as a network router and requires a complete external Wi-Fi network to operate. RJ45 Ethernet adapter support also not integrated, as CineView M7 is meant to use its on-board Wi-Fi module for more convenient wireless camera control connection.
• 4. Setup Your Camera Network Config If you chose “Wi-Fi”, then choose “Camera Access Point Mode” if you want a camera hotspot ( most recommended way ), or browse the available Wi-Fi network and connect to an existing network.

It’s recommend to later choose “Easy Connection” and “Automatic Setting” as this option will let the camera automatically detect what IP Address is available and avoid address conflicts.

After this select “Create New Function Settings”, and then choose “No Auth. (general user)”. (*Extra Note: If you’re taking the camera hotspot approach, you may need to connect CineView to the camera hotspot Wi-Fi network halfway through to validate and save the settings.) —— If you chose “Ethernet”, please then select “Setup with Network Connection”.

Also recommended to later choose “Easy Connection” and “Disable” IPv6.

Later process generally the same with Wi-Fi except that you don’t connect to wireless networks.

• 5. Check Current Camera IP Address After the network configuration, you just need to go into “Connect”, select the network settings slot you just saved to, and confirm to use this network config. Then go to “Connection Settings”, enter “Check Settings”, here displays the current network status of the camera, including the current IP address.
• 6. Connect the CineView M7 Now connect your CineView M7 to the corresponding network. Then tap on the top status bar, and find Camera Control setting in the menu.

Switch to “IP” option in “Connection Method”, then switch to “Canon C-series XC”, and now you input the IP address of the camera, tap on confirm button, the Accsoon SEE App will automatically connect to the camera. (*If you can’t find the “IP” option, remember: Wireless Camera Control Connection is Only Available in Monitor Mode. )

• Notes to Pay Attention to:
• 1. White Balance Settings It’s recommended to switch the White Balance Increment (shown as “C. Temp. Increment”) to “Kelvin”. Choosing Mired for now will not cause camera to respond very differently, but later firmware may introduce unexpected behavior like